Xerox QLS-8100XE Uživatelský manuál Strana 63
- Strana / 185
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
QLS-8100 Xe 4-17
3 Press the + or – key until the desired horizontal offset setting is
displayed.
Offset settings range from <– 600 to -> 600 pixels (or dots). On the
QLS-8100 Xe, there are 12 pixels per millimeter. The final image position
will be constrained by the label width.
4 Press the SELECT key to confirm your choice.
Partially printed labels under the printheads will finish printing using
the previous offset to ensure color alignment. During this time, you
cannot adjust the cross web or horizontal offset values. The new
horizontal adjustment will affect subsequent labels.
Note: Setting the offset via software will always override this setting. You
can set the offset via Color QuickLabel 99.
- Operation & Setup Guide 1
- Trademarks 4
- Limited Warranty 4
- Obtaining Service 5
- Contact Information 5
- Ownership Information 5
- Table of Contents 7
- QLS-8100 Xe iii 9
- Chapter 1: 11
- Quick Start 11
- QuickLabel Systems media 12
- Quick Start Guide 13
- 1-4 Quick start 14
- Chapter 2: 15
- Physical Setup 15
- Unpacking the Printer 16
- Printer Orientation 17
- Features of the QLS-8100 Xe 18
- Side view 19
- Rear Panel View 20
- QLS-8100 Xe 2-7 21
- 2-8 Physical setup 22
- QLS-8100 Xe 2-9 23
- 2-10 Physical setup 24
- Power Connection 25
- Computer Connections 26
- RS-232 Serial Port 27
- 2-14 Physical setup 28
- Print Servers 29
- Utility Port Connection 30
- Compressed Air Connection 31
- Cover Switch 32
- Chapter 3: 33
- Loading Media 33
- QLS-8100 Xe 3-3 35
- Loading Label or Tag Media 36
- QLS-8100 Xe 3-5 37
- Adjusting the Media Sensor 39
- Calibrating for Media Types 40
- QLS-8100 Xe 3-9 41
- Calibration Bad 42
- Calibrating Reflective Media 43
- Calibrating Continuous Media 45
- Chapter 4: 47
- Keypad Controls 47
- Keypad Layout and Functions 48
- Deletes all labels 49
- SELECT to confirm 49
- Menu Overview 50
- QLS-8100 Xe 4-5 51
- QLS-8100 Xe 4-7 53
- Print Intensity 54
- Intensity 55
- Head 1 = 16 55
- Pause: Adjust 55
- Print Line Adj 58
- Head 1 = +0 58
- Cross Web Adj 60
- Head 1 = <-2 60
- Vertical 61
- Offset = + 16 61
- Horizontal 62
- Offset = < 16 62
- QLS-8100 Xe 4-17 63
- Display Cntr 64
- Pause: System 64
- Cut Offset 65
- Label Reprint 66
- Copies = 1 66
- Pause: Operation 66
- Cal & Setup Menu 67
- Test Print 68
- Test Pattern = 2 in 68
- Pause: Cal & Setup 68
- Baseline = +0 69
- Baseline = 0 70
- Printer Settings 71
- Print With Head 1 71
- Operation Menu 73
- Synchronize Labels 76
- Cannot Synchronize 77
- Continuous Media Cal 77
- Printer Is Paused 77
- Ribbon Menu 78
- Drop/Lift Adjust 79
- Head 3 = 6 80
- Pause: Ribbon 80
- Ribbon Sensor 81
- Communications Menu 82
- Parallel Mode 83
- Pause: Communications 83
- RS232 Baud Rate 84
- RS232 Handshaking 85
- Hardware 85
- TCP/IP Address 86
- 192.168.255.1 86
- TCP/IP Subnet Mask 87
- 255.255.255.1 87
- TCP/IP Gateway 88
- 0.0.0.0 88
- System Menu 89
- Memory Card 90
- Write Protect ON 90
- Front Panel Lock/Unlock 91
- Front Panel Unlock 92
- QLS-8100 Xe 4-47 93
- Memory Card - Formatting 94
- 10:42 am 95
- 2002, Aug 26 96
- Factory Reset 97
- Options Menu 99
- Enabled 100
- Pause: Options 100
- Press SELECT 100
- Cut Flag 101
- Pull Back 103
- Synch Required 104
- Applicator 104
- Operation 105
- Chapter 5: 105
- Powering the Printer On 106
- Memory Card Detection 107
- Printer Indicators 108
- Error Messages 109
- Drive Roll Up 110
- Format Error 110
- label name: error # 110
- Drive Roll Up/No Air 110
- QLS-8100 Xe 5-7 111
- 5-8 Operation 112
- Ribbon Detection 113
- System Failure 113
- Excessive Heat 113
- Detected on Head x 113
- Color Alignment 114
- QLS-8100 Xe 5-11 115
- Common Adjustments and Tasks 116
- Evaluating Print Quality 117
- 5-14 Operation 118
- RUN with NO AIR ? 119
- Press: Select 119
- Printing Labels 120
- Chapter 6: 121
- Advanced Adjustments 121
- Printhead Tangency Alignment 122
- QLS-8100 Xe 6-3 123
- Ribbon Wrinkling Adjustments 124
- QLS-8100 Xe 6-5 125
- 6-6 Advanced adjustments 126
- Vertical Baseline 127
- Horizontal Baseline 128
- Chapter 7: 129
- Maintenance 129
- Recommended Tool List 130
- Routine Cleaning 131
- Head x Disabled 132
- Head x up 132
- SELECT to disable 132
- Refilling the Cooling System 133
- 7-6 Maintenance and repair 134
- QLS-8100 Xe 7-7 135
- Connect 12" Tube 136
- To Air Regulator 136
- Connect 36" Tube 136
- To Draining Receptacle 136
- Water Tube Connectors 136
- Printhead Replacement 137
- 7-10 Maintenance and repair 138
- QLS-8100 Xe 7-11 139
- Platen Replacement 140
- QLS-8100 Xe 7-13 141
- Drive roller replacement 142
- Pinch Roller Replacement 143
- 7-16 Maintenance and repair 144
- Firmware Upgrades 145
- 7-18 Maintenance and repair 146
- QLS-8100 Xe 7-19 147
- Insert CF Card and 148
- Press SELECT Key 148
- Forced Upgrade 148
- Appendix A: 149
- Physical Data 149
- QLS-8100 Xe Dimensions 150
- Appendix B: 153
- Specifications 153
- QLS-8100 Xe Specifications 154
- QLS-8100 Xe B-3 155
- B-4 Specifications 156
- Appendix C: 157
- Replacement Parts 157
- C-4 Replacement parts 160
- Appendix D: 161
- Color QuickLabel 99 161
- Pro setup 161
- QLS-8100 Xe D-3 163
- QLS-8100 Xe D-5 165
- Appendix E: 167
- Windows Printer 167
- Driver Setup 167
- Windows Printer Driver Setup 168
- QLS-8100 Xe E-3 169
- QLS-8100 Xe E-5 171
- To save the processed label: 173
- Appendix F: 175
- Format error codes 175
- F-2 Format error codes 176
- QLS-8100 Xe F-3 177
- F-4 Format error codes 178
- QLS-8100 Xe F-5 179
- F-6 Format error codes 180
- Appendix G: 181
- Menu Structure 181
- G-2 Menu Structure 182
- QLS-8100 Xe Menus 183
Související produkty a manuály pro Tiskárny štítků Xerox QLS-8100XE
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce